Tag: como destravar nintendo switch

Please be sure to update fusee when upgrading to 1.4.0. fusee-primary no longer exists, and will not work any more.

Note: The following was changed since pre-release:

• A bug was fixed in fusee that would cause a black screen when booting with nogc patches on and exFAT-supporting firmware installed.
• A bug was fixed that could cause the gdbstub to report the wrong file/module name when debugging homebrew.
• hbl was updated to version 2.4.3.

With thanks to the @switchbrew team, Atmosphère 1.4.0 is bundled with hbl 2.4.3, and hbmenu 3.5.1.

The following was changed since the last release:

• Support was added for 15.0.0.
  • mesosphère was updated to reflect the latest official kernel behavior.
  • ncm was updated to reflect the latest official kernel behavior.
• A number of minor issues were fixed and improvements were made, including:
  • The capacity limit on registered add-on contents was fixed in NCM to reflect the increase that occurred in 12.0.0.
  • An off-by-one was fixed in mesosphere when computing the new value for an address arbiter signaled with ModifyByWaitingCountIfEqual.
  • dmnt.gen2’s gdbstub now sanitizes thread names to prevent invalid characters from breaking gdb.
  • dmnt.gen2’s gdbstub now reports the architecture tag correctly when attached to 32-bit processes.
  • Support for program-specific html manual content overrides was added for non-hbl takeover context.
  • A bug was fixed in how emummc constructed the alternate Nintendo directory path.
    • Previously, this was using /*/Nintendo/Nintendo instead of /*/Nintendo.
    • Code was added to automatically move the old folders to the new ones when booting into emummc.
  • A bug was fixed in boot that caused an incorrectly low input voltage limit to be set.
• General system stability improvements to enhance the user’s experience.

• HOS 15.0.0 full support
• Fixed a regression on HOS 6.2.0 causing TSEC to hang hekate
• A new animated ticker line is now shown during bootlogo’s delay time
  It gives a nice visible feedback and a reminder to user to press VOL- if needed.
  It can be disabled by editing hekate_ipl.ini and setting noticker=1 in [config] section. (GUI option may come later.)
  That only disables the ticker for custom bootlogos, not the default hekate one.
• For new Mariko users, Auto HOS Power Off feature is now enabled by default
  Existing users, can enable it, as always, in Nyx -> Options -> Auto HOS Power Off.
• Added an error message in case payload launching fails
  Previously it wouldn’t show anything.
• Support for new dram chips
• Many under the hood improvements

• Fluid GUI for Mariko
  Nyx now uses HW rotation which extremely improves render times on Mariko
  The slow and waterfall-like rendering is now gone.
• Black Theme support
  Added experimental Black Theme aimed mostly for OLED panels.
  Can be enabled in Nyx Settings -> Color Theme -> Toggle Background.
  You need to select Save & Reload after that to really use it.
  For now it’s experimental as it needs some tweaks here and there.
• Added info about Switch Lite Sharp LQ055T1SW10 panel
• Fixed an issue that would create a massive stutter each time a tap was done on a window
  Noticeable on Mariko devices since it would create a 1s stutter. (On Erista it’s not visible.)
• Nyx Options was renamed to Nyx Settings to avoid confusion with hekate/general Options
• A warning icon together with reason is now shown if fuel gauge is in init state
• The partition manager, now also does a backup of payload.bin in case a full backup is not possible
  Now the total of backed up items in such a case is: hekate/Nyx files (bootloader), Mariko Warmboot Storage (warmboot_mariko) and payload.bin.
• Fixed an issue with XUSB which would break USB on Mariko in L4T after UMS usage
• Fixed an issue where if user pressed the invisible padding buttons on a pop up, it would close it.
• Fixed a heap corruption issue when entering emuMMC window which could hang Nyx
• Improved various error messages
• Many under the hood improvements